Gbc W25E WireBind User Manual download pdf (Page 5)

Guarantee

Operation of this machine is guaranteed for two years from date of

purchase, subject to normal use. Within the guarantee period, ACCO

Brands Europe will at its own discretion either repair or replace the

defective machine free of charge. Defects due to misuse or use for

inappropriate purposes are not covered under the guarantee. Proof

of date of purchase will be required. Repairs or alterations made by

persons not authorised by ACCO Brands Europe will invalidate the

guarantee. It is our aim to ensure that our products perform to the

speciﬁcations stated. This guarantee does not affect the legal rights

which consumers have under applicable national legislation governing

the sale of goods.

Wire binding instructions

For use with GBC 34 loop wire elements.

1. Set the wire

Lift the lid and punch handle to the upright position.

Place entire document so it rests on the lid.

Check the wire size (mm) needed using the pa

per thickness guide.

Measure your wire using the wire size guide.

urn the wire selector (located at the side of the machine) until the

number matches your wire size (5mm-14mm).

The machine will automa

tically prevent your wire from over closing,

and will adjust the margin depth.

Troubleshooting

• This machine has a recommended duty cycle of 5 operations per

minute, up to a maximum of 30 minutes on / 30 minutes off.

• This machine is ﬁtted with a thermal overload safety fea

ture. In

extreme circumstances, the motor may overheat which will activate

the safety feature. This feature will prevent the machine punching until

it has cooled sufﬁciently.

• The thermal overload switch will automa

tically reset after

approximately 15 minutes. The machine will then operate as if it had

been overloaded (see step 4 below).

2. Sort paper

For mana

ging large documents use the document separator.

Push the separa

tor into the document.

Lift the separa

tor upwards to reveal the ﬁrst stack of paper ready for

easy punching.

3. Set paper size

On manual machines,

ensure that the punch handle is in the upright

position before centering the paper.

Load the ﬁrst pa

per stack into the punch slot.

Centre the pa

per using the dial located at the front of the machine.

4. Punch paper

For manual punching: Lower the raised handle until the paper is

punched and support the machine when lifting the handle to the upright

position.

For electric punching (W25E only): Press the ‘punch button’

located on the right panel of the machine.

Note: If the machine is overloaded and fails to complete the punch

cycle, the red LED will be lit. Press the ‘punch button’ to cancel the red

LED. If this does not work contact the service helpline.

5. Wire binding

Open the hinged cover a

t the front of the machine to reveal the wire

binding channel.

Place the wire (open side up) on the wire support.

Feed each pa

per stack onto the wire and repeat until your document

is complete.

Support the document and wire on removal from the wire support.

Insert the document into the wire closing ja

ws (wire opening face

down).

Support the document and pull down the handle a

t the side of the

machine to close the jaws.

Binding tips:

To hide the spine of the wire:

•

Load the internal sheets onto the wire ﬁrst, repeating until all are

loaded.

•

Load the front PVC cover onto the wire element.

• Load the rear cover onto the wire element last.

• It is best to close the wire a little, check, and then close the wire a little

more until you are happy with the wire closure.

•

If the wire does not close properly, check that the machine has been

set to the correct wire size.

•

For further hints and tips please visit our website:

www.gbceurope.com

6. Maintenance

Please ensure the clippings tray is emptied on a regular basis. This may

prevent your machine from overloading.

W20:

When the clippings tray is full, you will see the clear window full of

clippings. Empty the contents of the tray to continue binding.

W25E:

When the clippings tray is full, a yellow LED will be lit. Empty the

contents of the tray to continue binding.

Security

A security slot is ﬁtted for use with leading makes of security leash. E.g.

Kensington Microsaver.

1 2 3 4 5 6 7 8 9 10 ... 37 38

Comments to this Manuals

No comments

Gbc W25E WireBind User Manual Page 5

Comments to this Manuals

Related products and manuals for Equipment Gbc W25E WireBind