Gbc 64Ct User Manual

SPIRE III Series LaminatorModels 44T, 64T, 64Ct, INSTALLATION & OPERATION MANUALDocument Number: 1723267 Rev. ADo not duplicate without written p

SPIRE III Series – Installation and Operating InstructionsPage 2-2

Page 3-1SPIRE III Series – Installation and Operating InstructionsModel 44T 64T 64CtOperating SpeedUp to 20 fpm (6 mpm) Maximum Temperature300 °F (149

SPIRE III Series – Installation and Operating InstructionsPage 3-2Fcc class a notIceThis device complies with Part 15 of the FCC Rules. Operation is s

Page 4-1SPIRE III Series – Installation and Operating Instructions WARNING: Do not attempt to service or repair the laminator. Failure to observe this

SPIRE III Series – Installation and Operating InstructionsPage 4-2locatIonProvide adequate space around the laminator as shown in the illustration. Th

Page 5-1SPIRE III Series – Installation and Operating Instructions5. Feature GuIdeFigure 4. Laminator identication. This chapter helps you identif

SPIRE III Series – Installation and Operating InstructionsPage 5-2emerGency stop sWItcHesFigure 5. Emergency Stop Switch near Operator Panel. Four E

Page 5-3SPIRE III Series – Installation and Operating InstructionsB. upper unWInd sHaFtThe Upper Unwind Shaft is used to hold lm or media that will b

SPIRE III Series – Installation and Operating InstructionsPage 5-4FootsWItcHFigure 10. Footswitch.The Footswitch allows you to start and stop the lam

Page 5-5SPIRE III Series – Installation and Operating InstructionssHaFt storaGe cradleFigure 13. Shaft Storage Cradle on Back of the Laminator.Use Sh

SPIRE III Series – Installation and Operating InstructionsPage iACCO Brands reserves the right to make changes to this publication and to the products

SPIRE III Series – Installation and Operating InstructionsPage 5-6rear taBle and optIonal IdlerFigure 16. Rear Table and Optional Idler.a. rear taBle

Page 5-7SPIRE III Series – Installation and Operating InstructionsremovInG tHe pressure plateTo remove the Pressure Plate:1. To unlock the Pressure P

SPIRE III Series – Installation and Operating InstructionsPage 5-83. Raise it until it is above the Front Main Roller. Figure 23. Feed Table in Rais

Page 5-9SPIRE III Series – Installation and Operating InstructionstensIon adJustment knoBsTurn the knobs clockwise to increase tension and countercloc

SPIRE III Series – Installation and Operating InstructionsPage 5-10control panelThe Control Panel is located on the right side of the machine and cont

Page 5-11SPIRE III Series – Installation and Operating Instructionsa. roller Heater temperature dIsplayDisplays the lower heater setpoint temperature.

SPIRE III Series – Installation and Operating InstructionsPage 5-12poWerFigure 30. Power Cord (44T, 64T).poWer panelThe Power Panel includes the Powe

Page 6-1SPIRE III Series – Installation and Operating Instructions6. operatIonsequence oF operatIonMode Photo Safety Sensor Clear and No Micro Switche

SPIRE III Series – Installation and Operating InstructionsPage 6-2loadInG FIlmThe SPIRE Series laminator runs poly-in and poly-out pressure sensitive

Page 6-3SPIRE III Series – Installation and Operating InstructionsFigure 35. Shaft slot indicator.3. Lift the driven end of the shaft out of the Sad

Page iiSPIRE III Series – Installation and Operating InstructionsIntroduction ...iFeatur

SPIRE III Series – Installation and Operating InstructionsPage 6-4Figure 38. Taping lm to the rewind tube.3. Make two full wraps around the rewind

Page 6-5SPIRE III Series – Installation and Operating InstructionsFigure 43. Pressing a threading card into the nip.13. Press the Footswitch and gui

SPIRE III Series – Installation and Operating InstructionsPage 6-610. Attach the film to the existing web on the Main Rollers. Make sure to carefully

Page 6-7SPIRE III Series – Installation and Operating Instructions8. Carefully grab the web (top and bottom film), from the front operating position

SPIRE III Series – Installation and Operating InstructionsPage 6-8precoatInG mount Boards Use this process to precoat the front of substrates with pre

Page 6-9SPIRE III Series – Installation and Operating Instructions3. Refer to “Pressure Sensitive Mounting - Decal - Front” for step-by-step instruct

SPIRE III Series – Installation and Operating InstructionsPage 6-109. Press the Footswitch. 10. As the materials feed into the rollers, pull the re

Page 6-11SPIRE III Series – Installation and Operating Instructions9. Press the Footswitch. 10. As the materials feed into the rollers, pull the re

SPIRE III Series – Installation and Operating InstructionsPage 6-1211. Press a threading card into the nip of the Main Rollers, pushing the laminates

Page 6-13SPIRE III Series – Installation and Operating InstructionsFIlm alIGnmentThe top and bottom supply rolls must be aligned as closely as possibl

SPIRE III Series – Installation and Operating InstructionsPage iiiFilm Alignment ...6-13Film Tensi

SPIRE III Series – Installation and Operating InstructionsPage 6-14

Page 7-1SPIRE III Series – Installation and Operating InstructionscarInG For tHe spIre serIes lamInatorThe only maintenance required by the operator i

SPIRE III Series – Installation and Operating InstructionsPage 7-2trouBlesHootInGSymptom Possible Cause Corrective ActionLCD does not illuminate on th

Page 7-3SPIRE III Series – Installation and Operating InstructionsWeee statementAt the end of its useful life, your product is considered to be Waste

SPIRE III Series – Installation and Operating InstructionsPage 7-4Glossary oF termsThe terms listed here appear in this manual or are commonly used in

Page 7-5SPIRE III Series – Installation and Operating InstructionsnotesDate Note

SPIRE III Series – Installation and Operating InstructionsPage 7-6

Page 7-7SPIRE III Series – Installation and Operating Instructions

© 2013 ACCO Brands. All rights reserved. ACCO® is a registered trademark ofACCO Brands. GBC® is a registered trademark of General Binding Corporation.

Page 1-1SPIRE III Series – Installation and Operating InstructionsYour safety, as well as the safety of others is important. Before you install or use

SPIRE III Series – Installation and Operating InstructionsPage 1-2WARNINGWARNUNGMUCHOCUIDADOATTENTIONRISQUE DEBROYEMENT.Tenir mains etvêtements a l&ap

Page 1-3SPIRE III Series – Installation and Operating InstructionsBefore you operate this machine, it is important that you read and understand the en

SPIRE III Series – Installation and Operating InstructionsPage 1-4saFety laBel locatIonsFigure 1. SPIRE III Series safety label locations.Inside pan

Page 2-1SPIRE III Series – Installation and Operating Instructions2. WarrantylImIted 90-day WarrantyACCO Brands USA LLC, ACCO Brands, 4 Corporate Driv